silikontrac.blogg.se - Sewage ejector pump installation diagram

#Sewage ejector pump installation diagram manuals#
#Sewage ejector pump installation diagram install#
#Sewage ejector pump installation diagram skin#

Sump and sewage pumps often handle materials that can transmit illness or disease upon contact with skin and other tissues.

Wear adequate Personal Protective Equipment when working on pumps or piping that have been exposed to wastewater.

Proper venting of sewer and effluent gases alleviates poisonous gas buildup and reduces the risk of explosion and fire from these flammable gases.

Vent basin in accordance with local code.

#Sewage ejector pump installation diagram install#

To avoid hazards, install a double pole disconnect near the pump installation. In 208/230V installations, one side of the line going to the pump is always “hot”, whether the float switch is on or off.Any person who is unaware of the dangers of this pump system, or has not read this manual, can easily be injured by the pump system. Do not allow any person who is unqualified to have contact with this pump system.Do not allow children to play with the pump system.All pump/pump system installations shall be in compliance with all applicable Federal, State, and Local codes and ordinances.Modifications may affect seals, change the electrical loading of the pump, or damage the pump and its components. Do not modify the pump/pump system in any way.Exercise caution using tools and do not use electronic devices or have live, exposed electrical circuits in or around basins, open covers and vents. Prevent introduction of foreign objects into basin as sparks could ignite these gases. Sewage and effluent systems produce and may contain flammable and explosive gases.These pumps are not to be installed in locations classified as hazardous in accordance with the National Electric Code®, ANSI/NFPA 70.If rotating elements inside pump strike any foreign object, sparks may occur. Do not use this product with or near flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc.When used, electrical outlets shall be simplex of the appropriate rating.

Overloaded branch circuit wires will get very hot and can catch on fire.

This product requires a separate, properly fused and grounded branch circuit, sized for the voltage and amperage requirements of the pump, as noted on the nameplate.

Overloaded wires will get very hot and can catch on fire. Extension cords can overload both the product and extension cord supply wires.

Do not use an extension cord to power the product.

Avoid contact with plug ends after removing from energy source.

Some products may have internal capacitors that could cause shock.

Single-phase 208/230V pumps shall only be operated without the float switch by using the circuit breaker or panel disconnect.

Unprotected power and control (switch) cords can allow water to wick through ends into pump or switch housings, causing surroundings to become energized.

Protect the power and control cords from the environment.

Do not use this product in applications where human contact with the pumped fluid is common (such as swimming pools, fountains, marine areas, etc.).

The electrical power supply shall be located within the length limitations of the pump power cord, and for below grade installations it shall be at least 4 ft.

This will damage the power cord, and could expose the electrically live wires inside the power cord.

Do not lift or carry a pump or a float assembly by its power cord.

Do not enter the water if the water level is higher than the PPE protection or if the PPE is not watertight.

Always wear dielectric rubber boots and other applicable Personal Protective Equipment (PPE) when water is on the floor and an energized pump system must be serviced, as submerged electrical connections can energize the water.

Do not handle or unplug the pump with wet hands, when standing on damp surface, or in water unless wearing Personal Protective Equipment.

Failure to properly ground the pump system can cause all metal portions of the pump and its surroundings to become energized. Do not bypass grounding wires or remove ground prong from attachment plugs. Pump shall be properly grounded using its supplied grounding conductor.Do not remove cord and strain relief, and do not connect conduit to pump.All electrical and safety practices shall be in accordance with the National Electrical Code®, the Occupational Safety and Health Administration, or applicable local codes and ordinances.All installation and maintenance of pumps, controls, protection devices, and general wiring shall be done by qualified personnel.Always disconnect pump(s) from power source(s) before handling or making any adjustments to either the pump(s), the pump system, or the control panel.Accidental contact with electrically live parts, items, fluid, or water can cause serious injury or death.

#Sewage ejector pump installation diagram manuals#

12.2 Related Manuals / Resources Safety Precautions